Showing 145–160 of 170 results

  • A34 – HANDRAIL BRACKET

    POA
    Used to carry handrails along walls or fix structures back to walls. Tube passes through in long lengths, can be joined using the A8 or A9. Can be slid down a post and used for connecting a kick plate. Also for fixing hoardings, signs etc.
    # Ø A B C D E F
    526.9 76 57 55 45 8 5
    633.7 92 65 58 48 10 10
    742.4 112 84 60 48 10 10
    848.3 112 80 68 54 10 10
    View Size Chart
    Clear selection

  • A32 – CLAMP ON TEE

    POA
    Used for adding to and modifying an existing structure. Similar to the A2.
    # Ø A
    526.9 50
    633.7 54
    742.4 64
    848.3 74
    960.3 90
    View Size Chart
    Clear selection

  • A31 – SWIVEL TEE

    £5.70 +VAT
    Offset handrail spigot clamp accepts tube through top of the ‘T’, the spigot inserts directly into another clamp. Used for off setting rail from a post, can be rotated through 360°. Used with A6 and A2. Also use with A10 for wall mounted rail.
    # Ø A B C
    633.7 56 33 33
    742.4 62 42 36
    848.3 72 48 41
    View Size Chart
    Clear selection

  • A30 – SOCKET TEE & CROSSOVER

    POA
    This clamp is used on racking for the 90º connection of a vertical support to a horizontal load carrying rail. The rear outlet is available for a horizontal tie across the section.
    # Ø A B C
    526.9 31 35 41
    633.7 42 40 48
    742.4 54 49 60
    848.3 60 54 68
    960.3 62 68 86
    View Size Chart
    Clear selection

  • A28 – CROSS OVER

    POA
    Gives 90º crossover joint. Used in guardrail installations. Rails are passed through in long lengths and joined using the A8 or A9. Can be used for connection of a horizontal racking member to a vertical support, garment rails etc.
    # Ø A B
    526.9 36 32
    633.7 42 40
    742.4 54 49
    848.3 60 54
    960.3 62 68
    View Size Chart
    Clear selection

  • A27 – VARIABLE ELBOW

    POA
    Variable Elbow that allows two horizontal tubes to be connected and an angle created that is either greater or less than the standard 90 degrees
    # Ø A B
    633.7 48 44
    742.4 60 54
    848.3 68 64
    View Size Chart
    Clear selection

  • A26 – FOUR SOCKET CROSS

    POA
    Frequently used in structures that have many uprights, such as racking. This clamp ties a centre upright, which passes through the central hole, with four horizontal tubes. All connections are at 90º to each other.
    # Ø A B C
    526.9 32 82 82
    633.7 43 96 96
    742.4 48 120 120
    848.3 50 136 136
    960.3 54 175 175
    View Size Chart
    Clear selection

  • A24 – THREE SOCKET CROSS

    POA
    Frequently used to tie uprights with horizontal tubes in three directions all at 90º to the upright.
    # Ø A B
    526.9 88 44
    633.7 96 48
    742.4 120 60
    848.3 136 68
    960.3 176 88
    View Size Chart
    Clear selection

  • A23 – ADJUSTABLE TWO SOCKET CROSS

    POA
    Variable angle clamp enables tubes to be connected between angles 30º - 45º. Used for angled lower rail(s) joint to a vertical post on stairs. A3 can be used in association for top rail connection. A46 swivel clamp is an alternative.
    # Ø A
    742.4 146
    848.3 178
    View Size Chart
    Clear selection

  • A22 – CROSS TEE

    POA
    Used for a 90º connection of a lower rail(s) to an intermediate vertical post, the vertical post must remain continuous while the rail is joined in each side of the clamp. Usually complimented with the A4 when used for guardrailing.
    # Ø A
    526.9 88
    633.7 96
    742.4 120
    848.3 136
    960.3 175
    View Size Chart
    Clear selection

  • A21 – SHORT SWIVEL TEE

    POA
    Generally used in pairs (as shown). Allows angles between 90º - 180º. Used to change direction of rails in the same plane. Requires a central tube at the point of angle change. Consider the A7 as an alternative for the angle change.
    # Ø A
    633.7 58
    742.4 73
    848.3 81
    View Size Chart
    Clear selection

  • A20 – MID CORNER TEE

    POA
    A 90º corner joint, tube passes through the central hole. Used frequently for a lower rail(s). Often used in conjunction with the A18.
    # Ø A
    526.9 44
    633.7 48
    742.4 60
    848.3 68
    960.3 85
    View Size Chart
    Clear selection

  • A17 – GROUND SOCKET

    POA
    A ground socket that is cast into concrete and is flush with the finished ground level. Allows posts to be inserted and retained with a locking set screw. Posts can be easily removed at any time.
    # Ø A B
    633.7 126 125
    742.4 140 135
    848.3 140 138
    View Size Chart
    Clear selection

  • A16 – RAILING HORIZONTAL SIDE SUPPORT

    POA
    Provides a structural base plate as the A14, should not be used for heavy duty applications.
    # Ø
    View Size Chart
    Clear selection

  • A15 – SIDE PALM FIXING

    POA
    Provides a structural base plate to a vertical post that is required to be side mounted. This clamp is virtually flush to structure it is being fixed to. The tube does not pass through the clamp.
    # Ø
    View Size Chart
    Clear selection

  • A14 – RAILING VERTICAL SIDE SUPPORT

    POA
    Base for vertical posts for side mounting. Posts stand off from structure. Tube cannot pass through this clamp. Access to top fixing hole restricted, a threaded stud type bolt projecting a max. 25mm from structure needs to be fixed first.
    # Ø
    View Size Chart
    Clear selection