Showing 161–171 of 171 results
-
Key Clamp A12- BASE PLATE
POAProvides a structural base plate for the support of a vertical post typically for a guardrail. Two socket set screws give a rigid structural fixing. Recommended that the fixing down bolts be in line with the applied load.(i.e 90º to the rails)# Ø A B C D E F 526.9 112 76 64 76 11 8 633.7 128 88 80 88 11 10 742.4 144 102 80 88 14 10 848.3 156 117 92 88 14 10 960.3 165 120 98 130 14 18 
-
Key Clamp A11 – KICK PLATE BASE PLATE
POASpecific base plates designed for either 42.4mm or 48.3mm that will fix directly to the floor but will also accept a standard kick plate to the base. Has a number of applications but is particularly popular for fixed hand rail systems on roof or mezzanine areas where there is a need to avoid the drop of hazardous materials or tools from above# Ø A B 742.4 60 54 848.3 68 64 -
A10 – WALL FLANGE
POAA four holed plate providing a rigid fixing for handrails that terminate on walls. Ideal for securing garment railing structures to ceilings etc. Not to be used as structural fixings for supporting a vertical post on guardrails. Use A12 for this.# Ø A B C D E 526.9 63 48 81 6 4 633.7 65 48 84 6 4 742.4 75 51 98 8 6 848.3 85 54 112 8 6 960.3 96 60 130 11 6 
-
Key Clamp A10 – WALL FLANGE (Copy)
POAA four holed plate providing a rigid fixing for handrails that terminate on walls. Ideal for securing garment railing structures to ceilings etc. Not to be used as structural fixings for supporting a vertical post on guardrails. Use A12 for this.# Ø A B C D E 526.9 63 48 81 6 4 633.7 65 48 84 6 4 742.4 75 51 98 8 6 848.3 85 54 112 8 6 960.3 96 60 130 11 6 -
Key Clamp A9 – INTERNAL CONNECTOR
POAProvides a streamline flush joint in two tubes of the same dia. with a max. wall thickness 3.2 mm. Joints to be 150mm to the nearest support. Not for joining tubes that are subject to extreme loads, or where a direct tensile load is applied.# Ø A B 633.7 78 20 742.4 78 20 848.3 80 22 
-
Key Clamp A8 – EXTERNAL CONNECTOR
POAProvides a rigid joint for two tubes of the same diameter. Joints to be 150mm to the nearest support. Do not use for joining two tubes subject to extreme loads, i.e. a vertical post member supporting a guardrail. Use A9 for a streamline joint.# Ø A 526.9 64 633.7 90 742.4 96 848.3 96 960.3 125 
-
Key Clamp A7 – ELBOW
POATwo tubes can be joined with an angle range of between 105º - 165º. Joins the angled rail from a ramp or steps to level rails on a landing. Starts an angled rail from top of a first post. Can be used for obtuse angle change in a handrail.# Ø A 633.7 90 742.4 106 848.3 120 
-
Key Clamp A6 – 90 DEGREE ELBOW
POAThis is a 90º elbow joint. Used frequently for the termination of the top rail to the last post of a handrail. Also used for turning the rails around a 90º corner.# Ø A 526.9 44 633.7 48 742.4 60 848.3 68 960.3 86 
-
Key Clamp A4 – LONG TEE
POAProvides a 90º ‘T’ connection between two tubes. Used for the joint between a top rail and a vertical post. Allows tubes to be joined in the top part of the ‘T’. When used in guardrailing the A22 will compliment this for lower rail(s).# Ø A B 526.9 88 44 633.7 96 48 742.4 120 60 848.3 136 68 960.3 170 85 
-
Key Clamp A3 – 30-60 DEGREE SOCKET TEE
POA# Ø A B 633.7 54 73 742.4 63 89 848.3 68 102 
-
Key Clamp A2 – SHORT TEE
POAProvides 90º ‘T’ connection between two tubes. Used for the joint between end post and lower rail(s) when handrail is straight and level. Also for a top ‘T’ joint on a guardrail. Cannot join tube in top of ‘T’, use the A4 when this is required.# Ø A B 526.9 44 36 633.7 48 44 742.4 60 54 848.3 68 64 960.3 85 75 
